CuO Promotes the Formation of Halogenated Disinfection Byproducts during Chlorination via an Enhanced Oxidation Pathway.

Previous studies showed that cupric oxide (CuO) can enhance the formation of trihalomethanes (THMs), haloacetic acids, and bromate during chlorination of bromide-containing waters. In this study, the impact of CuO on the formation kinetics and mechanisms of halogenated disinfection byproducts (DBPs) during chlorination was investigated. CuO does not enhance the formation of DBPs (i.e., 1,1,1-trichloropropanone, chloroform, and trichloroacetaldehyde (TCAL) /dichloroacetonitrile) during chlorination of acetone, 3-oxopentanedioic acid (3-OPA), and aspartic acid, respectively. This indicates that the halogen substitution pathway cannot be enhanced by CuO. Instead, CuO (0.1 g L-1) accelerates the second-order rate constants for reactions of chlorine (HOCl) with TCAL, citric acid, and oxalic acid at pH 8.0 and 21 °C from <0.1 to 29.4, 7.2, and 15.8 M-1 s-1, respectively. Oxidation pathway predominates based on the quantification of oxidation products (e.g., a trichloroacetic acid yield of ∼100% from TCAL) and kinetic modeling. CuO can enhance the formation of DBPs (e.g., THMs, haloacetaldehydes, and haloacetonitriles) during chlorination of model compounds and dissolved organic matter, of which both halogen substitution and oxidation pathways are required. Reaction rate constants of rate-limiting steps (e.g., citric acid to 3-OPA, aromatic ring cleavage) could be enhanced by CuO via an oxidation pathway since CuO-HOCl complex is more oxidative toward a range of substrates than HOCl in water. These findings provide novel insights into the DBP formation pathway in copper-containing distribution systems.

Formation of regulated and unregulated disinfection byproducts during chlorination and chloramination: Roles of dissolved organic matter type, bromide, and iodide.

Algal blooms and wastewater effluents can introduce algal organic matter (AOM) and effluent organic matter (EfOM) into surface waters, respectively. In this study, the impact of bromide and iodide on the formation of halogenated disinfection byproducts (DBPs) during chlorination and chloramination from various types of dissolved organic matter (DOM, e.g., natural organic matter (NOM), AOM, and EfOM) were investigated based on the data collected from literature. In general, higher formation of trihalomethanes (THMs) and haloacetic acids (HAAs) was observed in NOM than AOM and EfOM, indicating high reactivities of phenolic moieties with both chlorine and monochloramine. The formation of haloacetaldehydes (HALs), haloacetonitriles (HANs) and haloacetamides (HAMs) was much lower than THMs and HAAs. Increasing initial bromide concentrations increased the formation of THMs, HAAs, HANs, and HAMs, but not HALs. Bromine substitution factor (BSF) values of DBPs formed in chlorination decreased as specific ultraviolet absorbance (SUVA) increased. AOM favored the formation of iodinated THMs (I-THMs) during chloramination using preformed chloramines and chlorination-chloramination processes. Increasing prechlorination time can reduce the I-THM concentrations because of the conversion of iodide to iodate, but this increased the formation of chlorinated and brominated DBPs. In an analogous way, iodine substitution factor (ISF) values of I-THMs formed in chloramination decreased as SUVA values of DOM increased. Compared to chlorination, the formation of noniodinated DBPs is low in chloramination.

Identification of the metabolites of rhapontigenin in rat and human by ultra-high-performance liquid chromatography-high-resolution mass spectrometry.

RATIONALE: Rhapontigenin, a stilbene compound isolated from the medicinal plant of rhubarb rhizomes, has shown a variety of biological activities. The purpose of this study was to identify and characterize the metabolites of rhapontigenin in rat liver microsomes, hepatocytes, urine, and human liver microsomes and hepatocytes. METHODS: The samples were analyzed by ultra-high-performance liquid chromatography combined with electrospray ionization quadrupole/orbitrap high-resolution mass spectrometry (UPLC-Q/Orbitrap-HRMS). The structures of the metabolites were interpreted by MS, MS/MS data, and elemental compositions. RESULTS: A total of 11 metabolites were detected and tentatively identified. M1, identified as piceatannol, was unambiguously identified using reference standard. Our results suggested that rhapontigenin was metabolized through the following pathways: (a) demethylation to produce piceatannol (M1), which further underwent oxidation to form ortho-quinone intermediate. This intermediate was reactive and conjugated with GSH (M10 and M11), which were further converted into N-acetyl-cysteine and excreted in urine. M1 also underwent sulfation (M8) and glucuronidation (M5); (b) direct sulfation, forming M6 and M7; and (c) direct glucuronidation to form M2, M3, and M4. Glucuronidation was a major metabolic pathway in hepatocytes and urine. CONCLUSIONS: The current study provides an overview of the metabolism of rhapontigenin, which is of great importance for us to understand the disposition of this compound.

Ag immobilized lignin-based PU coating: A promising candidate to promote the mechanical properties, thermal stability, and antibacterial property of paper packaging.

A lignin-based PU coating was prepared for paper-based green packaging. Two representative diisocyanate were used to prepare the coatings. Due to the rigid aromatic, the physical properties of the TDI system reached the maximum below the lignin content of 40%. The HDI that contains flexible aliphatic chains alleviated the brittleness of coating, and it showed physical advantages when the lignin content was more than 50%. Owing to the high lignin content, the coating presented enhanced thermal stability. After coated with the lignin-based PU coatings, the dry tensile strength of coated paper was improved by 126%. Amazingly, the wet strength was increased from 0.31 to 12.6 MPa with an improvement nearly 40 times. Based on the coordination of lignin, Ag+ was introduced into the PU matrix, which imparted the coating with excellent antibacterial ability. The colony forming units of E. coli and S. aureus were both less than 1. However, no inhibition halo was observed, which indicated that the Ag was firmly anchored on the coating and the antibacterial ability is only available when the bacterial contact the coating surface. The lignin-based PU coating with favorable sustainability and properties shows great potential in paper-based green packaging fields.

Design and Preparation of Multiple Function-Integrated Lignin/Tannin/ZnONP Composite Coatings for Paper-Based Green Packaging.

Lignin/tannin/ZnONP composite coatings were designed for paper-based green packaging. Multiple functions, such as high strength, moisture resistance, low air permeance, heat endurance, UV aging resistance, and antibacterial/mold properties, were successfully integrated into one biobased coating. Prepolymerization improved the physical properties of coatings at high lignin contents. The best ingredient ratio was: 40% lignin, 15% tannin, and 10% ZnONPs (based on tannin weight), and the as-prepared biocoating was labeled LTZn-10. After coated with LTZn-10, the tensile strength and bursting strength of the packaging were efficiently enhanced by more than 3 times and were dramatically increased by 51.6 and 5.6 times at the wet state, respectively, which reveals that the packaging has favorable moisture resistance and it can be used in high humidity environments. Scanning electron microscopy (SEM) proved that most of the pores on the paper were blocked by the coatings, which helped to decrease the air permeance by 10.3 times. Meanwhile, ZnONPs were evenly spread on the coatings, which endowed the packaging with excellent antibacterial/mold performance. No colony or mycelium was found in the test against Gram-negative/positive bacteria and eight common molds. Besides, antibacterial activity is only available while the bacteria come in contact with the coating and no active substances were released into the culture medium, which is a good property that can keep the cargo from contamination of antibacterial agents. In addition, the coated paper presented an improved Tg and thermal degradation temperature, indicating that the coated package has favorable thermostability and can maintain its outstanding physical properties in a wider temperature range. Lignin and tannin promoted the UV stability and service life of the coated paper, as a rare physical decrease was observed after UV aging for 72 h. The function-integrated biobased coating with favorable sustainability is a good candidate to be widely used in paper-based green packaging fields.

[The Preparation and Characterization of a New Solid Coagulant: Polymeric Ferric Silicate Sulfate].

As one of the most important water treatment agents, polysilicate coagulant, has been playing an important role in coagulation- flocculation, but it is prone to lose stability due to self-polymerization and the forming of silica gel. Therefore, research on the preparation of stable polysilicate coagulant has attract great attention. A new method to prepare a stable polysilicate coagulant (PSPF), was proposed in this paper. Its structure and morphology were characterized by using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) respectively. Fe species in PSPF was analyzed via Fe-Ferron complexation timed spectrophotometric method. The performance of PSPF was assessed by measuring micro-polluted water treatment efficiency. Primary chemicals, such as ferrous sulfate, sodium silicate, potassium dihydrogen phosphate, sodium carbonate, were used. The influence of those parameters affecting the preparation of PSPF, such as nSi/nFe, nP/nFe and nOH/nFe molar ratios were examined. The results showed that nSi/nFe of 1∶4, nP/nFe of 1∶6 and nOH/nFe of 1∶10 under 60 ℃ water bath for 30 min was the optimum condition for preparation. The FTIR spectrum indicated that PSPF was a kind of high molecular polymer, containing new groups (e.g., Si­O­Si and Fe­O­Si), which could increase the molecular weight，molecular chain and coagulation-flocculation efficiency. PSPF presented a cluster appearance similar to a network structure, which was conductive to adsorption-bridging capacity and precipitation sweeping. The increase of Fe(b) and Fe(c) as a result of Si increasing in PSPF improved the polymerization and solidification. The coagulation behaviors of PSPF that were largely affected by the coagulant dosage and pH, indicated that for pH and dosage at 6 and 8 mg·L-1, respectively, the residual turbidity and UV254 removal efficiency could achieve 0.33 NTU and 58.6%, respectively.

[Isolation and identification of a polyhydroxyalkanoate producing strain].

OBJECTIVE: We screened and isolated polyhydroxyalkanoate producing bacteria. METHODS: The strains were isolated from sludge from a beer brewery and screened by Sudan black B staining method. The isolated strains were identified according to their morphological features, physiological and biochemical analysis as well as 16S rRNA gene sequence analysis. The product extracted with hot chloroform from the isolated strain HG-B-1 was confirmed by Fourier transform infrared spectra. RESULTS: We isolated a bacterium, HG-B-1, from sludge collected from a beer brewery in Guangdong province, China. The yield of polyhydroxyalkanoates was 23.4% (w/w) based on dried weight of the bacterium cells when HG-B-1 grew in a medium containing saccharose. We analyzed 16S rRNA nucleotide sequence, and ascertained the phylogenetic position of the strain. CONCLUSION: Strain HG-B-1 with PHAs biosynthesis ability was identified as Stenotrophomonas maltophlia.